A8 Parts Forum  

Go Back   A8 Parts Forum > A8 D3 > D3 - Axles, Brakes, Suspension and Steering

D3 - Axles, Brakes, Suspension and Steering Brakes, Springs, shocks, steering racks, steering columns, suspension arms, wheel hubs etc.

Reply
 
Thread Tools Display Modes
  #1  
Old 3rd December 2019, 04:30 PM
snapdragon snapdragon is offline
Senior Member
 
Join Date: Nov 2011
Posts: 1,669
Default Front Wheel Bearing Replacement

After chasing a rattle on my right-front corner for years and replacing everything at least once, I bit the bullet and replaced the whole airstrut yesterday but the problem remains exactly the same. Im am nowleft with the wheel bearing/bearing housing.

I cannot find any how to posts about this and it is not something I have done on any car.

Has anyone else on here?

The car has done 280,000miles so I'm surprised they have lasted so long anyway (assuming it is the bearing).

This is the part..
https://www.ebay.co.uk/sch/i.html?_f...nkw=4E0498625D
will the hub part that the brake disk/wheel bolts to need pressing out/in?
Reply With Quote
  #2  
Old 3rd December 2019, 06:35 PM
MikkiJayne MikkiJayne is offline
Senior Member
 
Join Date: Jan 2012
Posts: 5,017
Default

Original Audi bearings last a spectacularly long time compared to other stuff I used to work with. 200K is not at all uncommon.

The bearing is a bolt-in component, but you are correct that the hub needs pressing out of the old one and then back in to the new one. The inner race will come with the hub as you remove it - the usual trick with that is to carefully grind a slot in to the race and then split it with a chisel. The bearing is carefully designed to make it impossible to use a bearing splitter.

Assuming you have access to a hydraulic press then that bit is fairly straightforward. Unfortunately getting the bearing off the car is not, as it is steel in an alloy upright and so galvanic corrosion usually makes it something of an ordeal. Normally I will remove the entire upright so I can put it in the bench vice. I will use the bolts as drifts to remove the old one since they are replaced anyway. Normally I'll cut the exposed thread off (thats obvious when you see it) and then unscrew the four bolts a turn or two, then support the strut well and just beat on the bolt heads until the bearing starts to move. Most of them I've done would be impossible to do on the car as you just can't get enough swing on a hammer.

That said, a bearing would usually groan or rumble rather than rattle. Have you tried the inner tie rod?
Reply With Quote
  #3  
Old 3rd December 2019, 07:52 PM
snapdragon snapdragon is offline
Senior Member
 
Join Date: Nov 2011
Posts: 1,669
Default

Thanks MikkiJayne, I see, thanks for sharing your knowledge - It sounds a bit much for me with no workshop/garage and with it bein winter, but I might see in Spring.

Yes, I replaced the tie-rod assemblies twice, greased the rack and adjusted preload. Did all the arms once and single ones thereafter.

I see from motortalk.de early A8s had a recall and they put 2 blobs of grease where the bearing housing mates with the upright due to microscopic movements.

Attachment 22496

Last edited by snapdragon; 23rd April 2020 at 09:18 AM.
Reply With Quote
  #4  
Old 3rd December 2019, 08:30 PM
MikkiJayne MikkiJayne is offline
Senior Member
 
Join Date: Jan 2012
Posts: 5,017
Default

I would be astounded if, after 13 salty winters, the bearing has any movement whatsoever in the upright! More likely it is jammed in there so tight with mixed metal corrosion it will take a sound beating with Mjölnir to get the damn thing out Definitely not a job for the road side in winter.

I reassemble them with aluminium anti-seize grease to prevent them corroding quite so badly again.
Reply With Quote
  #5  
Old 3rd December 2019, 09:00 PM
spannerrash spannerrash is offline
Senior Member
 
Join Date: Dec 2016
Posts: 399
Default

I did the front wheel bearings on my old B6 A4 which is a very similar setup. The bearing housings were stuck well and truly to the aluminium uprights. IIRC they only seem to go into the upright 5mm or so but that's enough to make em a real pain to remove.

I managed to remove them whilst still on the car with the use of a fairly heavy and long (to get the momentum) slide hammer bolted to the hub. I did half expect at the time that the hub would come out first but they never did. They needed the use of my works 20t press to get them out. Not saying it needed all 20t but they certainly didn't come out without a fight.

Galvanic corrosion, ya gotta love it,...... Or maybe not.
Reply With Quote
  #6  
Old 3rd December 2019, 09:30 PM
MikkiJayne MikkiJayne is offline
Senior Member
 
Join Date: Jan 2012
Posts: 5,017
Default

You know I never thought of a slide hammer. The first time I did one of these bearings I didn't have a slide hammer and so never changed my techique after I got one.

If it went through the centre of the hub and pulled on the back of the bearing, rather than pulling on the hub it would be sure to get the whole thing out, assuming its heavy enough. I might try that on the next one
Reply With Quote
  #7  
Old 4th December 2019, 10:47 AM
snapdragon snapdragon is offline
Senior Member
 
Join Date: Nov 2011
Posts: 1,669
Default

Thanks for the info.
https://www.youtube.com/watch?v=obtM__aJ9Yc
While a D4, it is similar and this is a slidehammer example.

https://www.autodoc.co.uk/mapco/13835694
It's £97 for a fully assembled hub/bearing but the brand is not SKF/FAG or similar, it is MAPCO.

They also do a the hub separately for £50 which could be pressed onto a top tier bearing by third party engineering services.
Reply With Quote
  #8  
Old 5th December 2019, 12:07 AM
Architex_mA8tey's Avatar
Architex_mA8tey Architex_mA8tey is offline
Moderator
 
Join Date: Jan 2009
Location: London/Oxford/Swindon
Posts: 7,648
Default

Quote:
Originally Posted by snapdragon View Post
After chasing a rattle on my right-front corner for years and replacing everything at least once, I bit the bullet and replaced the whole airstrut yesterday but the problem remains exactly the same. Im am nowleft with the wheel bearing/bearing housing.

I cannot find any how to posts about this and it is not something I have done on any car.

Has anyone else on here?

The car has done 280,000miles so I'm surprised they have lasted so long anyway (assuming it is the bearing).
Had a.knocking rattle on mine a few years ago and it turned out the be top suspension mounts worn and knocking against metal sometimes. That's the mounts at the top of the uprights where it comes through into the top of the front arch / wing. Replaced the mounts.and all noises went!
__________________

Confidence is the feeling you have before you know better . . . .
Audi A8 D2 3.7 Quattro Sport 1999 FL - Melange
2nd Place Winner - A8-Freunde Annual German Meet 2012 at Edersee
20" x 9" Bentley GTC Wheels with 385mm W12 Front Discs & Bentley Caliper Covers, Front Lowered on Coilovers, Xenons, Combined DRLs and LED Foglights to modified OEM front fog lamp position, Alcantara/Leather, Full Black Alcantara headlining + pillars and blind shelf, Bespoke Flat Bottomed Sports Steering Wheel, Dark Myrtle Wood, Autodim Mirrors, Bose, Blinds, Digital TV, Ski Hatch, Modified rear exhaust section for extra V8 Burble
Audi S8 D2 Final Edition 2002, Avus Silver with Red Leather Interior
Tiptronic with Sport mode button, Sony rear entertainment package, Bose sound system, Audi Navigation Plus, 20 inch Final Edition alloys, Full Cat Back Stainless Milltek exhaust, giving a great V8 burble
Audi A8L D2 4.2 Petrol with LPG - Ebony Black
Audi A8L D4 FL 4.0T Petrol twin turbo - Havana Black
Audi A2 1.6 FSi Sport - Dolphin Grey with Votex body kit and Red Leather Interior
and some other A8's A8L's and Mercs

Last edited by Architex_mA8tey; 5th December 2019 at 12:10 AM.
Reply With Quote
  #9  
Old 5th December 2019, 01:23 AM
snapdragon snapdragon is offline
Senior Member
 
Join Date: Nov 2011
Posts: 1,669
Default

Quote:
Originally Posted by Architex_mA8tey View Post
Had a.knocking rattle on mine a few years ago and it turned out the be top suspension mounts worn and knocking against metal sometimes. That's the mounts at the top of the uprights where it comes through into the top of the front arch / wing. Replaced the mounts.and all noises went!
Thanks AM8tey - where are these mounts? The top of the strut is a machined aluminium casting with three hollow centring 'spikes' that bolts with three large bolts onto the space frame/turret. If you meant this casting on the strut then it was replaced with the new strut assembly - or is there something up in the wheelarch?
Reply With Quote
  #10  
Old 5th December 2019, 08:17 AM
MikkiJayne MikkiJayne is offline
Senior Member
 
Join Date: Jan 2012
Posts: 5,017
Default

I think Neil might mean the D2. The D3 air strut is different though as its all one assembly.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:21 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.