First problem! Door handle
 

Hi all

As the temp have dropped, it seems my drivers door refuses to open from the outside.

The keyless system was a little odd in behaviour thinking back, in that I often had to actually pull the handle a little before recognition, whereas the other doors work with just proximity or the lightest of touches.

Now its just dead until the car has been driven a while, then it seems to work OK. I haven't yet checked for codes but will tonight or tomorrow.

I am likely stuck with stripping the door down and fitting a new handle or can copious contact cleaner / WD40 fix w temperamental one?

And where is the best source for one?

Thanks.

It may be that the colder weather is highlighting a poor battery.

I am aware that some of the electrical ‘luxury’ features (auto boot, softclose etc) are the first to be restricted to preserve battery energy when the battery is dying, often discovered at first unlock in the morning, especially after a couple of days of inactivity.

Also I believe that locking/unlocking via the key rather than the door handles prevents additional drain if you have an existing faulty handle(s).

Doesn’t completely solve the door handle issue but a frequent squirt of GT-85 does sometimes help, in the short term.

Thanks

Its only the drivers door and it wont unlock with the fob either. All other doors OK including the buttons seem ok.

Got these codes from a quick scan just a few mins ago, but will try to scan again tomorrow as I have clearded them now and need to have a drive:


3 Faults Found:
00193 - Rear Right Door Handle Touch Sensor (G418)
007 - Short to Ground
Freeze Frame:
Fault Status: 01100111
Fault Priority: 3
Fault Frequency: 14
Reset counter: 174
Mileage: 62592 km
Time Indication: 0
Date: 2017.10.14
Time: 00:50:52

00668 - Supply Voltage Terminal 30
002 - Lower Limit Exceeded - Intermittent
Freeze Frame:
Fault Status: 00100010
Fault Priority: 2
Fault Frequency: 3
Reset counter: 201
Mileage: 62656 km
Time Indication: 0
Date: 2017.10.27
Time: 21:42:56

00190 - Driver's Door Handle Touch Sensor (G415)
007 - Short to Ground
Freeze Frame:
Fault Status: 01100111
Fault Priority: 3
Fault Frequency: 14
Reset counter: 170
Mileage: 62768 km
Time Indication: 0
Date: 2017.10.31
Time: 00:15:36

and this one, odd that it states 0Km however

1 Fault Found:
02115 - Locking Unit for Central Locking
008 - Implausible Signal
Freeze Frame:
Fault Status: 01101000
Fault Priority: 2
Fault Frequency: 14
Reset counter: 174
Mileage: 0 km
Time Indication: 0

I'm having a similar problem where my driver door doesn't unlock when you touch it..all other doors seem to work fine.

Because the locking switch isn't working on the handle either, I'll be changing it with a brand new one which i got from TPS for £96. I painted the base coat myself and paid a local reputable bodyshop £20 for them to apply the clear coat lacquer.

I'll take some pictures of the process and post soon.

Please take pics for us Learners neeldub of the whole process+++

Hi

I don't suppose you have a link to the part you ordered?

Thanks
Alex

Hi unfortunately, in my haste to start and finish the task, i completely forgot to take take pictures..

however i found this guide from across the pond which has detailed instructions and pictures on how to remove the handle.. file attached.

I ordered from these guys:

http://tps.trade/

Part numbers are as follows:

Driver Side Door: 4E2837206G GRU
All Other Doors: 4E0839205G GRU

TPS can offer you slightly cheaper prices than main dealerships...in some cases you may even be able to open an account with them for significant discount on service items.. best to check with them how this can be done and the requirements..

Hope this information helps you all.

I can report that the repairs i did were successful and the door handle and electronics are all working 100%.

Thanks Neel. On scale 1-5 how hard would you rate it? Also how long did it take you? Thanks mate

Thanks a million +++

How easy is it to open an account with these guys?

Not sure buddy but you have to ask them.

Usually if you are a mechanic or have an automotive business. Maybe all you need is a vat registration number and a company name

Well because I've done it a few times now I know my exact way around and how to do it properly..so it took me about 1hr30mins from start to finish.

Might take you longer if you take time to explore the door mechanism and just getting to know your way around..

I would rate it 4 out of 5 and I strongly suggest you get some new door clips just in case you break the old ones.

+++
Think I need to see you next time I need to work on my 8;)

I need a new drivers door handle, I was thinking of fitting it then getting my smart repair man to spray it in situ. Is that a bad idea ?

Haha sure thing mate.. I'm in London.. and yourself?

It's best to get it done before fitting to the car.. makes everything much easier in my opinion. Otherwise you'd need to mask off a good portion of the car which will be time and cost consuming.

I've noticed that the electronics in my car are working much better now. Before, the battery was always discharging to the lowest level but since changing the handle, it's always holding a full charge.

London too mate. Bow

Ahh nice one mate.. anytime you'd like to work on the car give me a shout.. I'm in tottenham. I also have ODIS software for diagnosis which can work slightly better than VCDS for certain tasks.

I will hold you to that+++ need to change my brakes all round, never done it before, you got much experience with that?

I'm afraid not.. I steer clear of brake, engine and gearbox related work.. I prefer leaving that to the professionals as I don't have much experience working with them.